Amana Furnace Not Heating in Greater Vancouver — Causes & Repair

An Amana furnace that is "not heating" can mean a couple of things, and telling them apart matters. Sometimes the furnace comes on, the blower runs, but only room-temperature or cool air reaches the vents. Other times the furnace goes through its start-up but the burners never produce lasting heat, so the house slowly gets colder. Either way, the unit has power and is trying — which separates this from a furnace that won’t turn on at all — but something in the heat path is failing. For a Greater Vancouver homeowner in winter, that is uncomfortable, but the causes are usually well-defined and fixable.

Amana furnaces run on Daikin‘s control platform, and heat is delivered through a precise sequence: the thermostat calls, the inducer proves venting, the igniter heats, the gas valve opens, the burners light, the flame sensor confirms the flame, and only then does the blower push warm air. If any step in that chain fails, you can end up with a running furnace that never actually heats. Understanding the chain is how a technician — and an informed homeowner — narrows the cause quickly.

ROMA Heating & Cooling has diagnosed no-heat calls on Amana furnaces across Vancouver, Burnaby, Richmond, Coquitlam and the North Shore since 1999. Here are the most likely causes, the safe checks to try, and when to call.

Most likely causes of an Amana furnace not heating

Thermostat not calling for heat

A thermostat set to OFF or COOL, in FAN-ON mode (which runs the blower with no heat), with dead batteries or a wrong schedule, will leave you with air but no warmth. Safe check: set to HEAT, raise the setpoint, switch the fan to AUTO, and replace batteries.

Gas supply interrupted

If the gas shutoff at the furnace or meter is closed, or FortisBC service is interrupted, the burners can’t light. Safe check: confirm the manual gas valve at the furnace is open (handle parallel to the pipe) and that other gas appliances work.

Ignition failure — igniter or gas valve

If the hot-surface igniter has failed or weakened, or the gas valve isn’t opening, the burners never light and no heat is produced. Safe check: none internal; this is a technician’s job to test and replace.

Dirty flame sensor dropping the flame

The burners may light briefly, but a coated flame sensor fails to confirm the flame, so the board shuts the gas off within seconds — you feel a burst of warmth, then cold air. Safe check: none internal; a technician cleans or replaces the sensor.

Tripped high-limit or pressure switch

A restricted filter or blocked vent can trip a safety that prevents the burners from firing, leaving the blower to circulate unheated air. Safe check: replace the filter, open registers, clear the outdoor intake and exhaust terminals and the condensate line.

Blower running on a fan call only

If the thermostat fan is set to ON, the blower runs constantly and pushes cool air between heat cycles, which can feel like "not heating." Safe check: set the fan to AUTO so it only runs with heat.

Not-heating quick-reference

📞 Talk to a licensed ROMA furnace technician — (604) 704-0300

Safe things to try once

Begin at the thermostat: set it to HEAT, raise the temperature several degrees, switch the fan from ON to AUTO, and put in fresh batteries. Confirm the manual gas valve at the furnace is open and that your other gas appliances are working, which rules out a supply interruption. Replace the 1-inch filter, open all registers, and clear the outdoor intake/exhaust terminals and the condensate trap in case a safety has tripped. Then run one full cycle and feel the vents. If warm air returns and stays, one of those was the cause. If the furnace still runs without heating — cool air, or a brief warmth that dies — stop and call a licensed gas technician. Never bypass a safety switch, jump the flame sensor, or attempt work on the gas valve or burners yourself.

What a ROMA tech checks first

A running-but-not-heating Amana is diagnosed by walking the ignition sequence and finding the step that fails, and that is exactly what our technician does. We confirm the thermostat is truly calling for heat and the fan is on AUTO, verify gas is present and the manual valve is open, then watch a full start-up. If the igniter glows but the burners never light, we test the igniter and confirm the gas valve is opening with adequate supply pressure. If the burners light and then die within seconds, we measure flame current at the sensor — a coated flame sensor is one of the most common no-heat causes we see across Metro Vancouver, and cleaning or replacing it restores heat quickly.

If ignition is fine but a safety is stopping the burners, we work the airflow and venting path: filter, blower, high-limit, pressure switch, inducer and the intake/exhaust terminals, since a restriction or a condensate backup in our damp winters can trip a limit and leave the blower circulating cold air. We also check the simple traps that fool homeowners — a fan set to ON, a thermostat in a bad location — before condemning any part. Everything is confirmed with a meter and a full observed cycle so the fix addresses the real cause rather than the first suspect.

When you call (604) 704-0300, have this ready:

• The furnace model and serial number.
• Whether the air from the vents is cool, room-temperature, or briefly warm then cold.
• Whether the burners appear to light at all.
• Whether other gas appliances in the home are working.

A no-heat furnace during a Vancouver cold snap matters most for elderly or very young occupants — tell us the situation and we will prioritize your visit.

When it’s an emergency

No heat is uncomfortable, but the safety rules still come first. If you smell gas, leave the home and call FortisBC emergency and 911 from outside — do not troubleshoot. If a CO alarm sounds or anyone feels unwell with headache, dizziness or nausea, get everyone out and call 911. If you see soot around the furnace or smell burning, shut it off and call us. In a cold snap with no heat and vulnerable occupants, let us know when you call so we can prioritize.

Repair vs. replace

Most no-heat causes — a thermostat fix, a flame-sensor cleaning, an igniter, a cleared safety — are minor, worthwhile repairs that bring heat straight back. A gas valve or inducer replacement is a larger repair but usually still economical on a furnace with good years left. Replacement becomes the smarter option when a no-heat failure lands on an older furnace already showing other worn parts, or when a heat-exchanger concern turns up during diagnosis. In those cases a high-efficiency replacement with BC rebates may cost less over time; we will lay out both paths honestly and let you choose.

Keeping your Amana heating reliably

Most no-heat calls trace back to two preventable culprits: a dirty flame sensor and restricted airflow. Change the 1-inch filter on schedule and keep registers open so a starved furnace doesn’t trip a limit and blow cool air. Through the wet Metro Vancouver winter, keep the outdoor intake and exhaust terminals and the condensate drain clear so a safety never trips mid-sequence. Set the thermostat fan to AUTO so it isn’t circulating cool air between cycles and making a working furnace feel like it isn’t heating.

The parts you can’t service yourself — the flame sensor, igniter, gas valve and safeties — are exactly what an annual pre-season tune-up addresses. Our technician cleans the flame sensor, checks the igniter’s condition, verifies gas pressure and the safety circuit, and confirms the furnace lights and holds a stable flame that delivers real heat. That one visit prevents the majority of the no-heat calls we take in January. Ask about a maintenance plan when you call and we will keep your Amana heating dependably.

Why ROMA for Amana furnaces in Vancouver

ROMA Heating & Cooling is a TSBC-licensed gas contractor (Gas licence LGA0202903), bonded, insured and Red Seal-trained, rated 4.8 stars from 221 Google reviews. For a no-heat Amana we walk the full ignition sequence to find the failing step — ignition, gas, flame sense or a tripped safety — with upfront flat-rate pricing and no hidden fees. Estimates on installs are free, 0% financing is available OAC, and we work seven days a week. See our furnace repair service or book a free estimate.

We serve Vancouver, Burnaby, North and West Vancouver, Richmond, Surrey, Coquitlam and the Fraser Valley. No-heat calls surge during Metro Vancouver cold snaps, and most are resolved in a single visit once the failing step is found. Call (604) 704-0300, or reach our team with questions, and ask about maintenance plans to keep the heat reliable.

Frequently Asked Questions

Why is my Amana furnace running but not heating?

It usually means the furnace has power and is trying, but a step in the heat path is failing: no ignition, gas supply off, a dirty flame sensor dropping the flame, or a tripped high-limit or pressure switch. Check the thermostat, gas valve and filter first, then call ROMA at (604) 704-0300.

My Amana blows cool air even though the furnace is on. What's wrong?

First check the thermostat fan setting — if it’s set to ON instead of AUTO, the blower runs constantly and circulates cool air between heat cycles. If the fan is on AUTO and the air is still cool, the burners likely aren’t lighting or a safety has tripped, and it needs a technician.

The furnace warms up for a few seconds then blows cold. Why?

That brief-warmth-then-cold pattern usually points to a dirty flame sensor. The burners light, but the coated sensor can’t confirm the flame, so the control shuts the gas off within seconds as a safety measure. A technician cleans or replaces the sensor to restore steady heat.

Could a dirty filter be why my Amana isn't heating?

Yes. A clogged filter can trip the high-limit safety, which stops the burners while the blower keeps running — so you get air but no heat. Replace the 1-inch filter and open the registers. If heat doesn’t return or the problem recurs, have a technician check the limit and airflow.

Does ROMA fix Amana furnaces that aren't heating across Greater Vancouver?

Yes. ROMA Heating & Cooling walks the full ignition sequence to find why your Amana isn’t heating, across Vancouver, Burnaby, Richmond, Surrey and the North Shore. We are TSBC-licensed, bonded and insured, with priority scheduling in cold snaps. Call (604) 704-0300 seven days a week.

Reviewed by the ROMA Heating & Cooling team — TSBC-licensed gas contractor (Gas LGA0202903), serving Greater Vancouver since 1999. Updated July 2026.

{“@context”: “https://schema.org”, “@graph”: [{“@type”: “Service”, “name”: “Amana Furnace Not Heating in Greater Vancouver — Causes & Repair”, “serviceType”: “Furnace repair and fault diagnosis”, “description”: “Amana furnace running but not heating in Greater Vancouver? Learn the common causes, safe checks to try first, and when to call ROMA at (604) 704-0300.”, “provider”: {“@type”: “HVACBusiness”, “name”: “ROMA Heating & Cooling”, “telephone”: “+1-604-704-0300”, “address”: {“@type”: “PostalAddress”, “streetAddress”: “2800 Douglas Rd B”, “addressLocality”: “Burnaby”, “addressRegion”: “BC”, “postalCode”: “V5C 5B7”, “addressCountry”: “CA”}}, “areaServed”: [{“@type”: “City”, “name”: “Vancouver”}, {“@type”: “City”, “name”: “Burnaby”}, {“@type”: “City”, “name”: “Surrey”}, {“@type”: “City”, “name”: “Richmond”}, {“@type”: “City”, “name”: “Coquitlam”}, {“@type”: “City”, “name”: “North Vancouver”}, {“@type”: “City”, “name”: “West Vancouver”}, {“@type”: “City”, “name”: “New Westminster”}, {“@type”: “City”, “name”: “Delta”}, {“@type”: “City”, “name”: “Langley”}, {“@type”: “City”, “name”: “Maple Ridge”}, {“@type”: “City”, “name”: “Port Coquitlam”}, {“@type”: “City”, “name”: “Port Moody”}, {“@type”: “City”, “name”: “White Rock”}], “url”: “https://romaheating.ca/amana-furnace-not-heating-greater-vancouver/”, “about”: {“@type”: “Product”, “name”: “Amana furnace”, “brand”: {“@type”: “Brand”, “name”: “Amana”}}}, {“@type”: “FAQPage”, “mainEntity”: [{“@type”: “Question”, “name”: “Why is my Amana furnace running but not heating?”, “acceptedAnswer”: {“@type”: “Answer”, “text”: “It usually means the furnace has power and is trying, but a step in the heat path is failing: no ignition, gas supply off, a dirty flame sensor dropping the flame, or a tripped high-limit or pressure switch. Check the thermostat, gas valve and filter first, then call ROMA at (604) 704-0300.”}}, {“@type”: “Question”, “name”: “My Amana blows cool air even though the furnace is on. What’s wrong?”, “acceptedAnswer”: {“@type”: “Answer”, “text”: “First check the thermostat fan setting — if it’s set to ON instead of AUTO, the blower runs constantly and circulates cool air between heat cycles. If the fan is on AUTO and the air is still cool, the burners likely aren’t lighting or a safety has tripped, and it needs a technician.”}}, {“@type”: “Question”, “name”: “The furnace warms up for a few seconds then blows cold. Why?”, “acceptedAnswer”: {“@type”: “Answer”, “text”: “That brief-warmth-then-cold pattern usually points to a dirty flame sensor. The burners light, but the coated sensor can’t confirm the flame, so the control shuts the gas off within seconds as a safety measure. A technician cleans or replaces the sensor to restore steady heat.”}}, {“@type”: “Question”, “name”: “Could a dirty filter be why my Amana isn’t heating?”, “acceptedAnswer”: {“@type”: “Answer”, “text”: “Yes. A clogged filter can trip the high-limit safety, which stops the burners while the blower keeps running — so you get air but no heat. Replace the 1-inch filter and open the registers. If heat doesn’t return or the problem recurs, have a technician check the limit and airflow.”}}, {“@type”: “Question”, “name”: “Does ROMA fix Amana furnaces that aren’t heating across Greater Vancouver?”, “acceptedAnswer”: {“@type”: “Answer”, “text”: “Yes. ROMA Heating & Cooling walks the full ignition sequence to find why your Amana isn’t heating, across Vancouver, Burnaby, Richmond, Surrey and the North Shore. We are TSBC-licensed, bonded and insured, with priority scheduling in cold snaps. Call (604) 704-0300 seven days a week.”}}]}]}