The Vitodens 100-W turns up often in Metro Vancouver: in condo closets in Burnaby and Richmond, in townhomes in Coquitlam and Surrey, and in smaller houses across Vancouver where one wall-hung unit replaced a boiler and a tank. Owners tend to like it until the day it shows a code or the shower runs cold. This guide explains how the combi works in plain terms, what you can safely check and how ROMA Heating & Cooling repairs it across Greater Vancouver.
Safety comes first with any gas appliance. At the first smell of gas, get everyone out, touch no switches and call FortisBC’s emergency line and 911 from outside. If the CO alarm goes off or anyone has a headache, dizziness or nausea, leave and call 911.
How does the Vitodens 100-W work?
Like other condensing combis, it has one burner serving two jobs. When the thermostat asks for heat, the burner fires and a pump moves hot water through your radiators, baseboards or floors in a sealed loop. When a hot tap opens, a diverter sends the burner’s heat to a plate heat exchanger that warms fresh water as it flows through. Because it condenses, it pulls extra heat from its exhaust, producing acidic condensate that drains through a trap. Combustion air comes in from outside, and exhaust leaves through a sealed vent. The controls manage all of this, sometimes using an outdoor sensor to adjust heating temperature to the weather.
What symptoms point to which area?
Call a licensed ROMA gas technician — (604) 704-0300
| What you notice | Area it often involves on combis of this type |
|---|---|
| Radiators warm, taps cold | Diverter, flow sensing, plate heat exchanger |
| Taps hot, radiators cold | Diverter, pump, thermostat call |
| Nothing works, code shown | Ignition, flame sensing, gas supply, venting, condensate |
| Hot water swings hot and cool | Flow at the tap, sensors, hot water side restrictions |
| Pressure keeps falling | Leak in the heating loop, relief valve, expansion vessel |
| Lockouts in cold snaps | Condensate trap or frozen condensate line, iced vent |
| House cool on cold days though combi runs | Outdoor sensor or control settings, flow restriction |
This is a map of where to look, not a diagnosis. Codes on the display are clues we confirm by testing.
What can owners safely check?
- That the thermostat is on heat, above room temperature, with fresh batteries.
- That the combi’s power switch is on and its breaker has not tripped.
- Where the pressure needle sits compared with its usual cold position.
- Whether a hot water issue affects every tap or only one.
- That the outside vent and air intake are clear of leaves or snow.
- What the display shows; take a photo.
A single reset is acceptable where the manual permits. Everything behind the casing belongs to a licensed gas technician.
How does ROMA repair a Vitodens 100-W?
We confirm it is safe to test, then work through controls and settings, the ignition sequence and flame, gas supply at the combi, venting and intake, the condensate trap and line, diverter, pump, flow and temperature sensors, pressure and expansion vessel. When the failed component is proven, the repair is priced in writing for your approval. Gas, combustion and safety parts on a 100-W are always Viessmann originals or ones Viessmann specifies. Once fitted, the burner is analysed again, safety devices are re-tried, disturbed gas joints are leak-tested and both heating and hot water are run.
What local conditions affect this combi?
In condos, crowded closets restrict airflow and kink condensate lines. In houses, outdoor vents at ground level collect leaves, and condensate lines that run outside can freeze. In older homes where the combi was fitted to existing radiators or baseboard, magnetite sludge is common; the region’s water is soft, so the problem is not mineral deposits but black sludge that restricts the heat exchanger and wears the pump. We explain what we find and whether a flush and dirt separator would help.
How do you keep a Vitodens 100-W healthy?
A yearly service: condensate trap cleaned, combustion analysed, safety controls tested, pressure and expansion vessel checked, hot water side confirmed and settings reviewed. Keep the closet clear and the outdoor vent unobstructed. Our maintenance plans keep it on the calendar.
What do condo owners with a Vitodens 100-W need to know?
Many 100-W combis in Metro Vancouver were installed as original equipment in condo buildings, so a whole building’s units may be reaching similar ages at once. If your strata has seen several failures, it may be worth asking whether the building has a maintenance plan for in-suite appliances. For your own unit, keep the closet clear so the combi can breathe and be serviced, make sure nothing is stored against its condensate line, and know where its service switch is. The vent termination may be on common property; if it is damaged, the strata usually arranges the repair, and we can note what we see for them. Book a yearly service in your own name so you have a record for resale.
When should a Vitodens 100-W be replaced rather than repaired?
If the main heat exchanger leaks or is corroded, if faults keep recurring after proper repairs, if parts become hard to obtain, or if the repair approaches the cost of a new combi. We give you our honest view; the decision is yours.
How are repairs priced?
A flat rate in writing after diagnosis and before work. If a part must be ordered, we explain the wait and look for a safe way to keep heat or hot water going. Appointments run every day of the week, with urgent evening and weekend calls taken when a technician can go.
Is ROMA a Viessmann dealer?
No. We do not claim Viessmann dealer or factory status. ROMA is a licensed gas contractor that has worked across Metro Vancouver since 1999, with Technical Safety BC licence Gas LGA0202903, bonding and insurance, and 4.8 stars from 221 Google reviews.
Tell us what you have — the brand, the model, and what it’s doing — and we’ll come back with the honest picture. Call (604) 704-0300 or book a Vitodens 100-W repair anywhere in Greater Vancouver.
Learn more about ROMA’s related services.
Need a licensed gas technician in Greater Vancouver?
ROMA Heating & Cooling has served Metro Vancouver since 1999 — TSBC-licensed (Gas LGA0202903), bonded & insured, 4.8★ from 221 Google reviews. Upfront flat-rate pricing, free estimates on installs, 0% financing (OAC), no hidden fees, 7 days a week.
Frequently Asked Questions
Why does my Vitodens 100-W heat the radiators but not the hot water?
When heating works but taps stay cold, the hot water path is the likely area: the diverter that switches heat between heating and hot water, the flow sensing that detects an open tap, or the plate heat exchanger. A technician tests each to find the actual cause before any repair is quoted.
Can I look up what my Vitodens 100-W code means?
You can note it and tell us, but please do not act on online code lists. The same code can have several causes, inside the combi or in the venting, condensate or gas supply around it. We use the code as a starting point and confirm the fault by testing before repairing anything.
How often should a Vitodens 100-W be serviced in Greater Vancouver?
Every year, with late summer or early fall being the most useful time. A service cleans the condensate trap, checks combustion and safety controls, tests pressure and the expansion vessel, confirms hot water performance and reviews settings. Combis work year-round for hot water, so yearly servicing helps prevent breakdowns.
Does ROMA use Viessmann parts on the Vitodens 100-W?
For gas, combustion and safety components, including the gas valve, burner, electrodes, fan, control board and safety sensors, we use Viessmann or Viessmann-specified parts. For a few other components a correctly matched approved equivalent may be suitable, and we tell you before fitting it.
Reviewed by the ROMA Heating & Cooling team — TSBC-licensed gas contractor (Gas LGA0202903), serving Greater Vancouver since 1999. Updated September 2026.
What Greater Vancouver Homeowners Say
“Nelson worked hard to get the NTI unit fixed. He was always polite, courteous and on time.”
“As always Nelson was super efficient. Showed up on time and was quick to work. I had a full maintenance done on the fireplaces and furnace. He was awesome. I won’t use anyone else.”
“Excellent service. Andy had a spare Carrier inducer with him which saved us time.”
“Was very prompt to respond to our issues. Technician was scheduled for the day following my initial call.”
“Very professional heating company. Price is reasonable, excellent work.”
“Highly recommend this company. It was a pleasure dealing with Shawn and Nelson.”
“Professional and courteous technicians with attention to detail and customer needs.”
“Always great, friendly service. Serviced the hot water on-demand system. Honest and informative. Thanks!”
“Speedy response time, honest, and professional service from start to finish.”
Why Greater Vancouver Trusts ROMA Heating & Cooling
ROMA Heating & Cooling has installed, repaired and maintained heating and cooling systems across Metro Vancouver since 1999. Our team are TSBC-licensed gas fitters (Gas LGA0202903) and Red Seal-trained technicians — licensed, bonded and insured — and we back every job with upfront, flat-rate pricing and a 100% satisfaction guarantee. We hold a 4.8★ rating from 221+ Google reviews.
- Authorized for 30+ brands (Lennox, Carrier, Viessmann, Navien, Rheem & more)
- Upfront flat-rate pricing — no overtime or hidden fees
- Free, no-obligation estimates on new installations
- Locally owned & operated in Burnaby, BC
No Hidden Fees
Our service rates are transparent and easy to understand. You approve upfront, flat-rate pricing before we start — so you never get a bill you didn’t expect.
Licensed & Bonded
ROMA is a TSBC-licensed gas contractor (Gas LGA0202903). Our technicians are bonded, insured and Red Seal-trained — qualified for any heating or cooling system.
Free Estimates
We offer free, no-obligation estimates on new installations — furnaces, boilers, heat pumps, air conditioners, tankless and hot-water tanks.
