Greater Vancouver’s Trusted HVAC Experts Since 1999 · 4.8★ (221 reviews)

Gas Fireplace Pilot Assembly & Ignition Module Replacement in Greater Vancouver

TSBC-Licensed Gas Contractor · Gas LGA0202903Licensed, Bonded & InsuredServing Greater Vancouver since 19994.8★ (221 Google reviews)
Speak with a licensed ROMA technician todayCall (604) 704-0300Free Estimate
Quick answer: A gas fireplace that won’t ignite, or a pilot that lights but won’t stay lit, is almost always a pilot assembly or ignition module issue rather than something wrong with the gas supply itself. This is licensed gasfitter work — ROMA Heating & Cooling’s Red Seal-trained, TSBC-licensed technicians diagnose and repair both standing-pilot and electronic ignition (IPI) fireplace systems across Metro Vancouver. Call (604) 704-0300. Call ROMA at (604) 704-0300 or book a free estimate.

Nothing’s more frustrating than reaching for the remote or the wall switch on a cold, wet Vancouver evening and having your gas fireplace do nothing — or light briefly and then go dark. These are two of the most common fireplace service calls ROMA gets, and both usually trace back to the pilot assembly or, on newer systems, the electronic ignition module. ROMA Heating & Cooling’s licensed gasfitters service gas fireplaces across Vancouver, Burnaby, Richmond, Surrey, and the rest of Metro Vancouver, and pilot and ignition repairs are core, everyday work for our team.

Standing pilot vs. electronic ignition (IPI) systems

Get a Quick Quote — Right Here

Fast response from a licensed ROMA technician — no obligation.









4.8★ from 221+ Google reviews · Licensed & insured · TSBC LGA0202903

Prefer to talk now? Call (604) 704-0300

Older gas fireplaces typically use a standing pilot — a small flame that burns continuously, ready to ignite the main burner the moment the thermostat or switch calls for heat. Most fireplaces installed in the last decade or more use Intermittent Pilot Ignition (IPI), where the pilot only lights briefly, electronically, right before the main burner fires, then shuts off again — no continuous flame burning between uses. Both systems rely on a thermocouple or flame-sensing component to confirm the pilot is actually lit before allowing gas to flow to the main burner, which is a critical safety feature in either design, not something either system can safely operate without.

Common symptoms and what they typically mean

📞 Talk to a licensed ROMA HVAC technician — (604) 704-0300

  • Pilot lights but won’t stay lit, going out shortly after you release the igniter or control
  • Fireplace won’t ignite at all, even though you can hear or see the igniter attempting to spark
  • Remote or wall switch does nothing, even with the pilot lit (IPI systems)
  • Fireplace ignites inconsistently — sometimes on the first try, sometimes not
  • A clicking sound from the igniter with no flame appearing at all
SymptomLikely cause
Pilot won’t stay litWorn thermocouple or thermopile no longer holding the gas valve open
No ignition attempt at all, no sound or sparkFailed ignition module, dead batteries (on battery-backup IPI systems), or a wiring issue
Clicking or sparking but no flamePilot orifice blockage or a gas supply issue at the pilot line
Remote works intermittentlyWeak remote batteries, signal interference, or a receiver issue in the ignition module
Fireplace was working, then suddenly stopped after being off for a seasonDust or debris accumulation in the pilot assembly over the off season, common in Vancouver’s damp climate

Why this is licensed-gasfitter work, not a DIY swap

The pilot assembly and ignition module sit at the exact point where gas, spark, and flame-sensing safety components all meet. A pilot assembly that’s reassembled slightly wrong, or a thermocouple that isn’t seated and calibrated correctly, can let gas flow without reliable flame confirmation — which is precisely the failure mode these safety components exist to prevent. In BC, gas fireplace repair of this kind legally requires a licensed gasfitter, and ROMA’s technicians carry TSBC gas licence LGA0202903 and are Red Seal-trained for exactly this work.

What a diagnostic visit for pilot or ignition issues looks like

A ROMA technician starts by confirming which type of system you have — standing pilot or IPI — since the diagnostic path differs between them. On a standing-pilot system, we test the thermocouple or thermopile output with a meter to see whether it’s producing enough millivolt signal to hold the gas valve open, which tells us definitively whether that component needs replacing or whether the issue lies elsewhere, such as a dirty pilot orifice restricting the flame itself. On an IPI system, we check the ignition module’s power supply, battery backup if equipped, and the spark or hot-surface igniter’s condition, along with the flame sensor that confirms the pilot actually lit before allowing main burner gas flow. Because these systems are built with layered safety checks, a fault in any one component usually shows up as a very specific, repeatable symptom, which is why an accurate diagnosis matters more than guessing and swapping parts.

Once the faulty component is identified, ROMA sources a replacement matched to your fireplace’s make and model rather than a generic universal part, since pilot assemblies and ignition modules are built to specific tolerances for their burner design. Most repairs are completed in a single visit once the correct part is confirmed, though older or discontinued models occasionally need a part ordered in, which we’ll tell you upfront rather than leaving you guessing about timeline.

Rather have a licensed pro handle it? Fast, honest help across Greater Vancouver.Call (604) 704-0300Free Estimate

There is a homeowner-safe step worth trying first: if your fireplace uses standard batteries in the remote or a battery-backup ignition module, replacing those batteries is a reasonable first check before calling — dead batteries are a surprisingly common cause of a fireplace that seems to do nothing at all, and it’s a genuinely safe, tool-free fix. Beyond checking batteries and confirming the wall switch or remote itself works, opening the pilot assembly, adjusting the pilot flame, or replacing the ignition module should always be left to a licensed technician. If at any point you smell gas, leave the home immediately and call FortisBC’s emergency line and 911 rather than continuing to troubleshoot.

ROMA Heating & Cooling has serviced gas fireplaces across Metro Vancouver since 1999, and our technicians repair and replace pilot assemblies and IPI ignition modules on the brands common in this market. If your fireplace won’t light or won’t stay lit, call (604) 704-0300 or book online for a diagnostic visit, and see our gas fireplace installation and repair page for the full range of service we provide.

Why this is licensed-gasfitter work, not a DIY repair

A pilot assembly or electronic ignition module sits directly in the gas path — it includes the gas orifice, the pilot burner or hot-surface igniter, and (on standing-pilot systems) the thermocouple or thermopile that proves the pilot flame is lit before the main gas valve is allowed to open. Disturbing any of these components without the right training risks an incomplete gas seal or a safety device that no longer shuts the system down correctly if the flame goes out. In BC, gas fireplace work falls under TSBC licensing requirements, and ROMA’s Red Seal-trained gasfitters (Gas Licence LGA0202903) handle every step of pilot and ignition diagnosis and replacement.

Standing-pilot vs. electronic ignition — why the fix looks different

Older gas fireplaces often use a standing pilot that stays lit continuously, monitored by a thermocouple or thermopile. Newer units use intermittent pilot ignition (IPI) or direct spark/hot-surface ignition, where the pilot only lights when you call for heat and a flame sensor confirms ignition electronically. A standing-pilot fireplace that won’t stay lit is usually a thermocouple issue; an IPI system that won’t ignite at all more often points to the ignition module itself, a blocked pilot orifice, or a wiring/sensor fault. ROMA identifies which type of system your fireplace uses before recommending a fix, since the replacement parts and diagnostic steps are different for each.

What a pilot/ignition service visit involves

ROMA’s technicians start with a visual inspection of the pilot flame (color, size, and stability), a check of the gas supply pressure, and a test of the safety shutoff behavior — confirming the system correctly cuts gas flow if the pilot or main flame fails. If the fault traces to the ignition module, thermocouple, or pilot orifice, we source a replacement matched to your fireplace’s brand and system type, install it, and re-test the full ignition sequence along with the safety shutoff before finishing the visit. Every gas fireplace service call from ROMA finishes with that safety verification, not just a “does it light” check.

Ready to book? Get a free estimate from ROMA.

Need a licensed HVAC technician in Greater Vancouver?

ROMA Heating & Cooling has served Metro Vancouver since 1999 — TSBC-licensed (Gas LGA0202903), bonded & insured, 4.8★ from 221 Google reviews. Upfront flat-rate pricing, free estimates on installs, 0% financing (OAC), no hidden fees, 7 days a week.

📞 Call (604) 704-0300Get a Free Estimate

Frequently Asked Questions

Why does my fireplace pilot light but then go out?

This is most often a worn thermocouple or thermopile that isn’t generating enough signal to hold the gas valve open once you release the igniter. It’s a common, repairable issue on standing-pilot systems.

My remote does nothing at all — is that the ignition module?

It could be, but check remote and ignition module batteries first, since dead batteries are a common and easily fixed cause on IPI systems before assuming the module itself has failed.

Is it safe to keep trying to light the pilot myself if it won't catch?

A few normal attempts following your manual’s instructions are fine, but if it repeatedly won’t light or you smell gas at any point, stop and call ROMA rather than continuing to try, or leave the home and call FortisBC and 911 if you smell gas.

What's the difference between a standing pilot and IPI system for repair purposes?

A standing pilot burns continuously and relies on a thermocouple; IPI systems ignite electronically only when needed and use an ignition module. Diagnosis and parts differ between the two, which ROMA identifies during the visit.

Can I replace the thermocouple or ignition module myself?

No — this work involves gas supply, spark, and flame-safety components together, and BC requires a licensed gasfitter for this type of repair on a gas fireplace.

Reviewed by the ROMA Heating & Cooling team — TSBC-licensed gas contractor (Gas LGA0202903), serving Greater Vancouver since 1999. Updated August 2026.

What Greater Vancouver Homeowners Say

4.8/5 from 221+ verified Google reviews

“Nelson worked hard to get the NTI unit fixed. He was always polite, courteous and on time.”

Chris Tipple · Verified Google review

“As always Nelson was super efficient. Showed up on time and was quick to work. I had a full maintenance done on the fireplaces and furnace. He was awesome. I won’t use anyone else.”

Tammy D · Verified Google review

“Excellent service. Andy had a spare Carrier inducer with him which saved us time.”

Steven E · Verified Google review

“Was very prompt to respond to our issues. Technician was scheduled for the day following my initial call.”

jason l · Verified Google review

“Very professional heating company. Price is reasonable, excellent work.”

Jessica Feng · Verified Google review

“Highly recommend this company. It was a pleasure dealing with Shawn and Nelson.”

Charlotte Stipp · Verified Google review

“Professional and courteous technicians with attention to detail and customer needs.”

Ted Laursen · Verified Google review

“Always great, friendly service. Serviced the hot water on-demand system. Honest and informative. Thanks!”

Wah Gee · Verified Google review

“Speedy response time, honest, and professional service from start to finish.”

Lauren McCaughey · Verified Google review

Read more reviews Call (604) 704-0300

Request Your Free Estimate

Fast response from a licensed ROMA technician — no obligation.









4.8★ from 221+ Google reviews · Licensed & insured · TSBC LGA0202903

Prefer to talk now? Call (604) 704-0300

Why Greater Vancouver Trusts ROMA Heating & Cooling

ROMA Heating & Cooling has installed, repaired and maintained heating and cooling systems across Metro Vancouver since 1999. Our team are TSBC-licensed gas fitters (Gas LGA0202903) and Red Seal-trained technicians — licensed, bonded and insured — and we back every job with upfront, flat-rate pricing and a 100% satisfaction guarantee. We hold a 4.8★ rating from 221+ Google reviews.

  • Authorized for 30+ brands (Lennox, Carrier, Viessmann, Navien, Rheem & more)
  • Upfront flat-rate pricing — no overtime or hidden fees
  • Free, no-obligation estimates on new installations
  • Locally owned & operated in Burnaby, BC

No Hidden Fees

Our service rates are transparent and easy to understand. You approve upfront, flat-rate pricing before we start — so you never get a bill you didn’t expect.

Licensed & Bonded

ROMA is a TSBC-licensed gas contractor (Gas LGA0202903). Our technicians are bonded, insured and Red Seal-trained — qualified for any heating or cooling system.

Free Estimates

We offer free, no-obligation estimates on new installations — furnaces, boilers, heat pumps, air conditioners, tankless and hot-water tanks.

Call Now Book Now
Emergency
Call NowFree Estimate
Scroll to Top