The average cost homeowners face for furnace repair is about $250. In most cases, homeowners spend between $130 and $400 to repair their furnace. Ultimately, furnace repair cost can range from $100 to $1,000 depending on the issue with the furnace.

What can cause a furnace to stop working?

A clogged furnace filter can cause a furnace to shut off. Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won’t warm up.

Should you repair or replace your furnace?

Furnace Age If your furnace is 10 years old or less, repairs should be effective. If it has reached 12 years or more, it’s time to consider replacement. If your furnace is more than 10 years old but having consistent issues, consult an expert.

What to check if your furnace isn’t working?

First, if your furnace has a pilot light, check to make sure it is lit. If this isn’t the problem, and your furnace does run on gas, check your water heater. If your water heater is working properly, you can eliminate gas supply as the problem. Next, check your air filter and verify it is clean.

Can hear your furnace click on but it does not fire up?

Most likely, your furnace is making a clicking noise and not providing heat because your furnace’s spark igniter is trying to ignite your pilot light or burners but is failing to do so. In other words, there’s an ignition system malfunction that needs to be fixed. Otherwise, your furnace won’t start.

Where is reset button on furnace?

The reset button is typically located inside the blower compartment on the side of the blower motor. When should I press the reset button? First, you need to locate your circuit breaker and switch off the power supply to the furnace. Then, if you see that the button is up, push it to reset your furnace.

Can a bad thermostat cause a furnace to short cycle?

Thermostat Malfunctions Broken or poorly placed thermostats can cause short cycling. Thermostats near heat sources or in direct sunlight can warm too quickly, signaling your furnace to shut off.

Why does my furnace ignite then go out?

The flame sensor is responsible for monitoring the gas burner. If the furnace starts then shuts off instantly it may be because the flame sensor is not able to identify the flame and the control board will shut off voltage to the gas valve interrupting the heat cycle.

Can you bypass a flame sensor?

Actually, you can bypass the flame sensor. the flame sensor is just a way of exposing the voltage on the flame sensor wire to the furnace burner flames. So you can connect the flame sensor wire to a screwdriver and put the screwdriver into the flames.

How much does it cost to replace a furnace flame sensor?

Depending on which furnace repair company you call, you can expect to pay anywhere from $350 to as much as $500 for a new flame sensor, plus the cost of the travel and diagnostic charge.

Can a dirty air filter cause furnace to stop working?

Clogs Lead to Furnace Failure: Can a clogged air filter cause a heater to stop? The answer is yes, and likely the costliest result of an improperly changed air filter may be the internal damage it deals to your central air conditioning and heating system.

Is it hard to replace a furnace?

Installing a new furnace is a fairly complicated process, and only licensed HVAC professionals have the required permits in your state. Furnace work is even more dangerous if your furnace burns fuel like natural gas or oil. The exhaust is extremely dangerous if your furnace isn’t tuned properly.

Is a new furnace worth it?

Assuming your furnace is replaced after 15 years of use (what we recommend) you would get a total fuel savings of $1,318.05. A 90% furnace would save you $927.45 in fuel, compared to an 80% furnace. You can see how a high-efficiency furnace may end up being worth the extra money it costs you at the time of purchase.

How efficient is a 20 year old furnace?

A 20 or 25 year old furnace has an efficiency rating of about 60%. Instead of warming your house, 40% of the heat generated through combustion of natural gas goes up the flue and out the chimney. High efficiency furnaces of today on average have an efficiency rating of 95%.

Should I replace my 30 year old furnace?

Regardless of the logic you follow, the 30-year mark is at or close to the maximum lifespan you should expect from your furnace. Even though furnaces can last 30 years or beyond, most experts recommend that you start shopping for a new furnace when your existing unit is 15 years old.
Book Online NOW & Get a FREE Quote

Furnace repair 1

ROMA™ | 20 Years Trust

Most Trusted Heating Service in BC

We covert the following areas:

we serve all major metropolitan areas and more

with over 25 Certified technicians in the field every day

24/7 Emergency Services


Vancouver