How much does gas furnace installation or replacement cost in Richmond?
Short answer: for a typical Richmond home, gas furnace installation / replacement runs roughly $6,000 to $12,000 (ballpark, before GST). Where your job lands depends on the equipment, access, venting, gas piping, permits and parts. ROMA Heating & Cooling gives an upfront flat-rate written quote before any work starts: call (604) 704-0300.
| Job (typical home, installed) | Ballpark range, before GST |
|---|---|
| Gas furnace installation / replacement | $6,000 – $12,000 |
| Furnace repair | $200 – $1,200 |
| Furnace tune-up | $150 – $300 |
Ballpark ranges for Greater Vancouver residential work, reviewed November 2026. Not a quote; your written quote is exact. Licensed gas contractor, Technical Safety BC LGA0202903.
Key takeaways
- Furnace installation cost in Richmond depends on equipment, access, venting, gas piping, permits and parts, so only a written quote is exact.
- ROMA gives an upfront flat-rate written quote before any work starts, so the installed price is settled in advance.
- Ballpark ranges are not a quote; a site visit confirms what your specific house needs.
- Ask what the installed price includes, since permits, venting and gas piping can change the total.
Richmond’s gas furnace installation cost answer is mostly a post-1990s answer: the town’s housing stock is recent, and the figures — $3,500–$7,500 typical total, roughly $9,500 for a high-efficiency installed system, unit commonly $2,900–$6,400 — usually read in the friendlier half. Ballpark pricing only. Figures are typical published 2026 Canadian/BC market ranges — installed including labour, excluding applicable taxes, for a typical 1,500–2,000 sq ft home with usable existing ductwork. Your exact price requires a free, no-obligation estimate and an in-home technician evaluation.The published extras, plainly: flue conversion $400–$1,200; duct modifications $500–$3,000; disposal of the retired unit $300–$600; permits $100–$500. And the city’s own notes deserve the print: a high water table informs exterior work, and compact townhouses make the placement and access part of the planning, not a footnote.
Can you give me a ballpark on gas furnace installation cost in Richmond?
Yes: $3,500–$7,500 typical, about $9,500 at the high-efficiency end, unit band $2,900–$6,400. Then the extras. A post-1990s home with its original unit and workable ducts is the honest benchmark around here — the equipment is at a believable age for its generation, and the quote usually reads clean.
| What you are paying for | Published range |
|---|---|
| Typical total installed (1,500-2,000 sq ft, usable ducts) | $3,500-$7,500 |
| High-efficiency installed system | Up to ~$9,500 |
| Furnace unit (95%+ models at high end) | $2,900-$6,400 |
| Flue conversion for condensing models | $400-$1,200 |
| Duct modifications | $500-$3,000 |
| Disposal of old unit | $300-$600 |
| Permits | $100-$500 |
What does the installed price include?
Call a licensed ROMA gas technician — (604) 704-0300
Unit delivery and placement, the flue route with the model’s class, gas and electrical connection, the start-up check, and the old unit’s removal. The machine is $2,900–$6,400. In the post-1990s stock, the included package is usually the honest package — and the water-table consideration lives in the exterior work, which the estimate should name rather than assume.
What raises the price?
The four extras — flue conversion $400–$1,200; duct modifications $500–$3,000; disposal $300–$600; permits $100–$500 — and Richmond’s own pair: compact townhouses where placement and access carry the building’s rules, and the high water table where exterior work is planned, not improvised. The quote that names both is the quote that survives the walk.
When is the best time to install a furnace in Richmond?
Spring and early autumn, as always; for the compact townhouse projects, the strata repair window is its own season, and the estimate should ask about it. Richmond’s winter is mild, so the changeover gap is easier than most of the region — which is exactly why a planned spring install costs nothing extra and keeps the peace.
What do furnace repairs cost in Richmond?
Diagnosis-led, consistently honest. Igniters, controls and blowers are the modest tier; exchangers, boards and majors are the heavy one. The coastal climate is a quiet factor too — moisture and salt air age metal and connections, and a technician’s look at the cabinet is part of the honest read, not the sales pitch.
Am I better off repairing or replacing?
Two numbers, one judgment: the repair and the installed replacement, age-weighted. A mid-life unit with a small fault: repair — the friendlier economics, especially when the installation was a clean one. An aging unit with a serious verdict: replacement, and in this stock the changeover is usually simple enough to make the decision painless.
How does a Richmond property shape the estimate?
Post-1990s homes with modern infrastructure are the town’s happy place: current duct design, sound panel capacity, and mechanical space that was planned rather than inherited. The high water table informs the exterior side of any project, and the compact townhouses carry the access-and-rules layer. The inspection reads your actual ground story before the repair or replacement decision, and the quote then fits the address, not the catalogue.
Carbon monoxide alarms on every level, tested as the seasons turn — the standing rule of gas heat, in compact spaces doubly so. If you smell gas: leave the house, call 911 and the gas utility’s emergency line from outside, and touch no switch, no thermostat, nothing.
Why do modern Richmond homes usually quote so cleanly?
The honest reason is the house’s era: post-1990s construction brought current duct design, panel capacity with headroom, and mechanical space planned when the unit lived there in the original plan. Those three facts are the difference between a swap that stays inside the typical band and a project that collects extras. Modern stock is the friendliest case in the region — and the friendliest case still earns its half-hour inspection, because ‘usually’ is a statistic rather than an address.
Which is the second honest note: no matter how new the house, the duct, the flue and the panel get read before the unit does. A clean era is a head start, not a guarantee, and the visit is the guarantee.
The modern-stock honest note: the era’s friendliness makes the swap a day, and the day after is the welcome silence — a system that runs its first season without notes is the reward, and the modern stock was built to give it.
The modern-stock note: a post-1990s home is the furnace trade’s gentle case, and the honest risk left is the small one — the era’s clean story still earns its inspection, because a panel story can age faster than a house. The families who book the half-hour get the certainty at one-tenth the price of the surprise, and the modern home’s famous smoothness is precisely what the visit protects. That is the whole gentle bargain of this city’s installs.
Ballpark pricing only. Figures are typical published 2026 Canadian/BC market ranges — installed including labour, excluding applicable taxes, for a typical 1,500–2,000 sq ft home with usable existing ductwork. Your exact price requires a free, no-obligation estimate and an in-home technician evaluation.
Tell us what you have — the brand, the model, and what it’s doing — and we’ll come back with the honest picture. Call ROMA Heating & Cooling at (604) 704-0300, or book an estimate and we’ll confirm the ground story and the number before the old unit goes anywhere.
Need a licensed gas technician in Greater Vancouver?
ROMA Heating & Cooling has served Metro Vancouver since 1999 — TSBC-licensed (Gas LGA0202903), bonded & insured, 4.8★ from 221 Google reviews. Upfront flat-rate pricing, free estimates on installs, 0% financing (OAC), no hidden fees, 7 days a week.
Frequently Asked Questions
Are Richmond homes all in the easy band for furnace installation?
Mostly, but not all — and honest language matters. The post-1990s stock usually runs the clean path, but the pre-1990s pockets still exist with era ducts and flue questions, and the compact townhouse layer carries access rules. The published $3,500-$7,500 band holds all of them; the inspection decides which end your address sits near.
How does the high water table affect furnace work in Richmond?
It shapes the exterior conversations: where anything lands inches off the ground, the placement and any exterior work is planned around the water profile rather than discovered mid-project. The machine and the published bands are unchanged; the planning is real and the honest estimate names it.
Do compact Richmond townhouses cost less or more to fit?
The unit often costs — or at least the class is smaller — and the access and rules layer adds the planning. Net honest answer: the machine is usually mid-band, and the project gains a coordination line rather than a price line. An early estimate lets the strata window and the budget agree before the winter.
Is coastal moisture worth worrying about for a Richmond furnace?
Worth a scheduled for, not a worry about. Sealed coast-adjacent air does age metal and connections, so the honest care plan is the seasonal check and clean at the unit — technician work, part of the standing plan. It costs a small ritual and returns the long life the estimate assumes.
Reviewed by the ROMA Heating & Cooling team — TSBC-licensed gas contractor (Gas LGA0202903), serving Greater Vancouver since 1999. Updated September 2026.
How much does furnace installation cost in Richmond?
Furnace installation cost in Richmond depends on the furnace you choose, where it sits in the house, how the venting and condensate drain will be routed, and what ductwork or gas piping needs updating. ROMA provides a free estimate and an upfront flat-rate written quote. Call (604) 704-0300 or email info@romaheating.ca for exact pricing.
Richmond homes are built differently from much of Metro Vancouver, and that shows up in furnace quotes:
- Few basements. Because so much of Richmond sits low and close to the water table, furnaces are often in a garage, a hallway closet, a shallow crawlspace or an attic rather than a basement. Each location has its own clearance, access and drainage rules.
- Condensate drainage. A condensing furnace makes water. In homes with no floor drain near the furnace, a condensate pump and a longer drain run are common additions.
- Venting. Older split-levels in Seafair, Broadmoor and Steveston often vent the old furnace into a shared metal chimney. A new condensing furnace usually vents out a side wall, and the water heater left in the old vent needs checking.
- Townhouses. Many Richmond townhouse complexes have strata rules on vent locations, exterior penetrations and contractor parking.
- Ducts and returns. Undersized returns or crushed crawlspace ducts limit any new furnace, so we point them out and price fixes as options.
Everything is listed in writing, including optional upgrades like a heat pump for cooling or a new thermostat, so you can choose what matters.
What does ROMA do when installing a new furnace in Richmond?
ROMA sizes the furnace to your house, removes the old unit, installs the new one with code-compliant gas, venting and drainage, and then commissions it with instruments. A standard installation is usually done in one day; attic or crawlspace installs, new vent routes or a condensate pump can stretch it to a second day.
- Before quoting, we measure the home and run a heat loss calculation, accounting for windows, insulation and any renovations.
- On installation day we protect floors and the route to the furnace, shut off gas and power, and remove the old unit.
- We set the new furnace, build new transitions to the existing ducts, and seal connections.
- We connect gas with a new shut-off and sediment trap, and leak-test the work.
- We install venting and combustion air piping to a code-approved termination, away from windows, doors and neighbours’ openings.
- We run the condensate line to a drain, or install a condensate pump where needed.
- We start the furnace, perform combustion analysis, check temperature rise and airflow, and test for carbon monoxide.
- We set the thermostat, show you the filter and shut-off, and go through your paperwork.
In many Richmond crawlspace and attic installs we find ducts that were crushed or disconnected years ago, which explains a cold room that no furnace could fix. We check this before quoting so the new system actually delivers heat where you need it.
How soon can ROMA install a furnace in Richmond?
ROMA books furnace estimates and installations 7 days a week. If your furnace has failed, we will try to come quickly, and same-day assessments are possible when the schedule allows. Planned installations are booked on the day you choose, and fall fills up fast, so earlier is easier.
When you call or book online, it helps to have:
- A photo of the rating plate on the current furnace.
- A photo of where the furnace sits: garage, closet, crawlspace or attic, and how you reach it.
- Photos of the vent pipe and the water heater beside the furnace, if there is one.
- Strata rules and parking details for townhouses.
A simple owner checklist before the estimate: clear a path to the furnace, note which rooms are always too cold or too warm, and find any old paperwork for the current unit. If the furnace is in the attic or crawlspace, let us know how the hatch is reached. Those details help our technician quote accurately on the first visit, so you are not waiting for a second appointment just to measure.
Why choose a licensed gas contractor for a furnace installation in Richmond?
A furnace installation connects gas, venting and combustion in your living space, and each must be done to code for your family’s safety. ROMA is a Technical Safety BC licensed gas contractor (Gas LGA0202903), bonded and insured, and has installed furnaces across Metro Vancouver since 1999.
- Gas permits for Richmond installations go through Technical Safety BC, so your installation is on record.
- Installation estimates are free and every quote is a flat rate in writing.
- Financing is available on approved credit if you would rather spread the cost.
- ROMA holds a 4.8-star rating from 221 Google reviews.
- If a FortisBC rebate program may apply to your equipment choice, we let you know so you can check eligibility before you commit.
If you smell gas, get everyone out, do not use switches, and call FortisBC’s emergency line and 911 from outside. If a CO alarm goes off or anyone feels headachy or nauseous, leave and call 911.
Where can a furnace go in a Richmond home, and what does each location involve?
Since few Richmond homes have a basement, furnace location shapes much of the installation. The table compares the common locations we work in and what each means for your quote and for future service.
| Furnace location | Common in | What to plan for |
|---|---|---|
| Garage | Ranchers and split-levels across Richmond | Raised platform or protection from vehicles, vent route to outside |
| Hallway or utility closet | Townhouses and newer homes | Tight clearances, return air sizing, condensate pump if no drain |
| Crawlspace | Older homes in Seafair, Broadmoor and Steveston | Low access, moisture, duct condition, service access in future |
| Attic | Some newer homes and renovated houses | Platform and access, condensate safety pan, insulation around ducts |
| Furnace paired with outdoor heat pump | Any location with room for an outdoor unit | Outdoor placement, salt air near the dyke, condensate from both units |
To compare equipment options, see our heating installation page, or learn how a heat pump can pair with a gas furnace for summer cooling.
Which Richmond neighbourhoods and nearby areas does ROMA serve?
ROMA installs furnaces across Richmond, including Steveston, Seafair, Broadmoor, Terra Nova, Thompson, Hamilton, East Richmond, Ironwood and the City Centre. We also serve Vancouver, Delta, Burnaby and New Westminster from our office in Burnaby.
Planning a new furnace, or need to replace one that has quit? Call (604) 704-0300 or email info@romaheating.ca with photos of your current furnace and its location, and we will arrange a free estimate.
More questions we hear about this
How much does it cost to install a furnace in Richmond?
It depends on the furnace you choose, its location in the house, venting and condensate routing, and any duct or gas line updates. ROMA offers free estimates with an upfront flat-rate written quote listing every item. Call (604) 704-0300 or email info@romaheating.ca with photos of your current furnace and its location for exact pricing.
How long does furnace installation take in a Richmond home?
A standard replacement is usually completed in one day. Attic or crawlspace installations, a new vent route, or adding a condensate pump can extend the job to a second day. We give you a realistic timeline when we quote, and we commission and test the furnace thoroughly before leaving so you are not left with surprises.
Do you help register my new furnace warranty?
Yes. After installation we give you the model, serial number and install date in writing and help you complete the manufacturer registration. Many manufacturers require registration within a set time after installation, and coverage terms vary by brand, so we recommend completing it promptly and keeping your ROMA paperwork with the furnace manual.
Can you install a furnace in a Richmond townhouse with strata rules?
Yes. Many Richmond townhouse complexes have rules about vent terminations, exterior wall penetrations, work hours and parking. Share your strata rules when you book, and we will plan the vent route and schedule to match. If council approval is needed, we can provide the installation details your strata needs to review in advance.
Related guides: Furnace installation richmond
What Greater Vancouver Homeowners Say
“Nelson worked hard to get the NTI unit fixed. He was always polite, courteous and on time.”
“As always Nelson was super efficient. Showed up on time and was quick to work. I had a full maintenance done on the fireplaces and furnace. He was awesome. I won’t use anyone else.”
“Excellent service. Andy had a spare Carrier inducer with him which saved us time.”
“Was very prompt to respond to our issues. Technician was scheduled for the day following my initial call.”
“Very professional heating company. Price is reasonable, excellent work.”
“Highly recommend this company. It was a pleasure dealing with Shawn and Nelson.”
“Professional and courteous technicians with attention to detail and customer needs.”
“Always great, friendly service. Serviced the hot water on-demand system. Honest and informative. Thanks!”
“Speedy response time, honest, and professional service from start to finish.”
Why Greater Vancouver Trusts ROMA Heating & Cooling
ROMA Heating & Cooling has installed, repaired and maintained heating and cooling systems across Metro Vancouver since 1999. Our team are TSBC-licensed gas fitters (Gas LGA0202903) and Red Seal-trained technicians — licensed, bonded and insured — and we back every job with upfront, flat-rate pricing and a 100% satisfaction guarantee. We hold a 4.8★ rating from 221+ Google reviews.
- Authorized for 30+ brands (Lennox, Carrier, Viessmann, Navien, Rheem & more)
- Upfront flat-rate pricing — no overtime or hidden fees
- Free, no-obligation estimates on new installations
- Locally owned & operated in Burnaby, BC
No Hidden Fees
Our service rates are transparent and easy to understand. You approve upfront, flat-rate pricing before we start — so you never get a bill you didn’t expect.
Licensed & Bonded
ROMA is a TSBC-licensed gas contractor (Gas LGA0202903). Our technicians are bonded, insured and Red Seal-trained — qualified for any heating or cooling system.
Free Estimates
We offer free, no-obligation estimates on new installations — furnaces, boilers, heat pumps, air conditioners, tankless and hot-water tanks.
More ROMA services in Richmond
Part of our Gas Furnace Guide: Everything Metro Vancouver Homeowners Need to Know › Furnace installation & replacement
Related guides in this topic:
Real ROMA furnace work. These photos are from our own jobs, not stock images. See more in our work gallery or call (604) 704-0300.
