Fireplace Xtrordinair Gas Fireplace Igniter Replacement in Greater Vancouver
When a Fireplace Xtrordinair won’t spark to life, the igniter system is the first place to look. The igniter generates the arc that lights the pilot — without it, the entire ignition chain stops before it starts. ROMA Heating & Cooling diagnoses and replaces Fireplace Xtrordinair igniters across Greater Vancouver, with gas-licensed technicians experienced on the full FX range and OEM-spec parts for prompt service.
Fireplace Xtrordinair in Greater Vancouver
Travis Industries’ Fireplace Xtrordinair brand has been installed extensively across Metro Vancouver since the 1990s — in Burnaby bungalows, North Shore luxury homes, Coquitlam townhouses, and Surrey new builds. Many of the 44 Elite, 36 Elite, 550 TraDITIONal, and 616 Insert models in service today are 10–20 years old, an age at which igniters, pilot assemblies, and thermopiles begin to require attention. ROMA’s familiarity with the full FX range means faster, more accurate diagnosis for Greater Vancouver homeowners.
How FX Ignition Works — Standing Pilot vs IPI
Fireplace Xtrordinair models use one of two ignition approaches:
- Standing pilot (millivolt) — the pilot burns continuously. The igniter is a manual piezo button or push-button module that creates a one-time spark to light the pilot at the start of the season (or after a shut-off). Once the pilot is lit and the thermopile generates voltage, the igniter is no longer active in normal operation.
- Intermittent Pilot Ignition (IPI) — the pilot lights only on demand. An electronic IPI module fires the spark igniter every time the fireplace is called for heat, then shuts the pilot off again when the burner goes off. IPI systems save gas but put more cycle demand on the igniter and module.
Igniter failure symptoms differ slightly between these two systems, which is why a proper diagnosis is more efficient than a parts swap.
Common Igniter Failure Symptoms on Fireplace Xtrordinair
| Symptom | Most Likely Cause |
|---|---|
| No spark when ignition button pressed (standing pilot) | Failed piezo module or broken igniter wire |
| Spark present but pilot won’t light (standing pilot) | Electrode tip worn, misaligned, or spark gap incorrect |
| IPI fireplace clicks repeatedly but pilot won’t catch | IPI module fault, electrode wear, or gas pressure low |
| Intermittent ignition — sometimes works, sometimes doesn’t | Cracked igniter wire insulation or loose connection |
| Spark heard but not visible at electrode | Carbon buildup on electrode tip diverting the arc |
ROMA’s Igniter Replacement Process
- System diagnosis — We test the igniter module, electrode, and wiring independently to confirm which component has failed before any parts are ordered or replaced.
- Gas isolation — The gas supply is confirmed off before accessing the pilot assembly area.
- Component replacement — The failed igniter module, electrode, or wiring is replaced with an OEM-spec FX-compatible part.
- Electrode gap and positioning check — Correct electrode-to-pilot-hood distance is confirmed per the FX service specification.
- Pilot lighting and operational test — We light the pilot, confirm hold, fire the main burner, and verify stable operation through the full ignition-to-shutdown cycle.
IPI Module Replacement
On Fireplace Xtrordinair models with Intermittent Pilot Ignition, the IPI control module drives the igniter and manages the pilot on/off cycle. When the module fails, the fireplace typically goes completely dead — no click, no spark, no response to the wall switch or remote. IPI module replacement is a complete swap of the control board; ROMA carries common FX IPI modules and performs the replacement under full gas-licensed procedure.
Igniter Service Across Metro Vancouver
ROMA reaches all of Greater Vancouver from our Burnaby base — Vancouver, North Shore, Coquitlam, Port Moody, Pitt Meadows, Maple Ridge, Surrey, White Rock, Langley, Richmond, and Delta. We stock FX-compatible igniter components for prompt service on the most common models. No DIY gas work, no unqualified shortcuts — professional gas-licensed igniter replacement that restores your Fireplace Xtrordinair to reliable operation.
Book Igniter Replacement
Call ROMA Heating & Cooling at (604) 704-0300 or email info@romaheating.ca. Gas-licensed and insured, serving Metro Vancouver since 1999.
What Our Customers Say
“My fireplace had issues and I needed to service my furnace. Roma was on time and they were able to fix the issues. Very happy.”
— Sébastien Hebert, Google review (★★★★★)
“Very happy with service — he got my fireplace working very quickly and was very courteous and professional.”
— Lara Fox, Google review (★★★★★)
Frequently Asked Questions
What does the igniter do on a Fireplace Xtrordinair?
The igniter (also called a spark igniter or piezo igniter) generates the high-voltage spark that lights the pilot flame when you press the ignition button or activate electronic ignition. Without a working igniter, the pilot cannot be lit — and without the pilot, the main burner cannot open.
How do I know if my Fireplace Xtrordinair igniter has failed?
The most obvious sign is no spark visible at the pilot assembly when you press the ignition button, or only a very weak spark that does not reliably light the pilot. You may hear a clicking sound but see no arc at the electrode tip. A professional inspection distinguishes between a failed igniter module, a worn electrode, and a faulty igniter wire.
Can I replace the igniter myself on a Fireplace Xtrordinair?
Adjusting or replacing components connected to the gas pilot assembly requires a BC gas licence. While the igniter itself is not a gas component, accessing it requires working around live gas fittings, and incorrect reassembly can create a hazard. ROMA technicians handle this as part of a complete pilot-system inspection.
Does the IPI module on newer Fireplace Xtrordinair models use a different igniter?
Yes — Fireplace Xtrordinair models with Intermittent Pilot Ignition (IPI) use an electronic module-driven igniter rather than a manual piezo. The spark electrode is similar in appearance but the driving electronics differ. ROMA carries components for both IPI and standing-pilot FX configurations.
How long does igniter replacement take?
A standard igniter replacement on a Fireplace Xtrordinair takes under an hour, including diagnosis, replacement, pilot lighting, and operational verification. Most visits are completed in a single call.
Related Guides & Services
- Gas Fireplace Repair
- Gas Fireplace Leak Detection
- Fireplace Maintenance & Service
- Emergency HVAC Repair
Call ROMA Heating & Cooling Today
For fast, professional diagnosis and repair anywhere in Greater Vancouver, call (604) 704-0300 or email info@romaheating.ca. prompt and after-hours service, gas-licensed and insured, serving the Lower Mainland since 1999.
What Greater Vancouver Homeowners Say
“Nelson worked hard to get the NTI unit fixed. He was always polite, courteous and on time.”
“As always Nelson was super efficient. Showed up on time and was quick to work. I had a full maintenance done on the fireplaces and furnace. He was awesome. I won’t use anyone else.”
“Excellent service. Andy had a spare Carrier inducer with him which saved us time.”
“Was very prompt to respond to our issues. Technician was scheduled for the day following my initial call.”
“Very professional heating company. Price is reasonable, excellent work.”
“Highly recommend this company. It was a pleasure dealing with Shawn and Nelson.”
“Professional and courteous technicians with attention to detail and customer needs.”
“Always great, friendly service. Serviced the hot water on-demand system. Honest and informative. Thanks!”
“Speedy response time, honest, and professional service from start to finish.”
Why Greater Vancouver Trusts ROMA Heating & Cooling
ROMA Heating & Cooling has installed, repaired and maintained heating and cooling systems across Metro Vancouver since 1999. Our team are TSBC-licensed gas fitters (Gas LGA0202903) and Red Seal-trained technicians — licensed, bonded and insured — and we back every job with upfront, flat-rate pricing and a 100% satisfaction guarantee. We hold a 4.8★ rating from 221+ Google reviews.
- Authorized for 30+ brands (Lennox, Carrier, Viessmann, Navien, Rheem & more)
- Upfront flat-rate pricing — no overtime or hidden fees
- Free, no-obligation estimates on new installations
- Locally owned & operated in Burnaby, BC
No Hidden Fees
Our service rates are transparent and easy to understand. You approve upfront, flat-rate pricing before we start — so you never get a bill you didn’t expect.
Licensed & Bonded
ROMA is a TSBC-licensed gas contractor (Gas LGA0202903). Our technicians are bonded, insured and Red Seal-trained — qualified for any heating or cooling system.
Free Estimates
We offer free, no-obligation estimates on new installations — furnaces, boilers, heat pumps, air conditioners, tankless and hot-water tanks.
ROMA Heating & Cooling is a trusted HVAC contractor serving Metro Vancouver since 1999. We specialize in furnace repair, heat pump installation, boiler services, air conditioning, and emergency heating solutions for residential, commercial, and government clients. Available for same-day and after-hours service, our certified technicians deliver fast, reliable, and affordable HVAC services across Greater Vancouver.

